Welcome, Guest. Please login or register.
October 17, 2017, 03:35:40 PM

Login with username, password and session length

Recent Topics

[Today at 03:13:56 PM]

[Today at 03:04:11 PM]

[Today at 03:02:41 PM]

by D.
[Today at 02:38:45 PM]

[Today at 02:21:28 PM]

[Today at 02:10:32 PM]

by D.
[Today at 02:08:05 PM]

[Today at 01:49:56 PM]

[Today at 01:27:50 PM]

[Today at 12:50:30 PM]

[Today at 12:48:32 PM]

[Today at 11:55:43 AM]

[Today at 11:12:25 AM]

[Today at 10:41:45 AM]

[Today at 10:10:24 AM]

[Today at 10:09:51 AM]

[Today at 09:59:30 AM]

by DG
[Today at 08:30:41 AM]

[Today at 08:03:25 AM]

[Today at 07:26:56 AM]

by DG
[Today at 07:20:46 AM]

[Today at 06:51:16 AM]

[Today at 05:22:58 AM]

[Today at 12:39:11 AM]

[October 16, 2017, 10:21:21 PM]

by Ghan
[October 16, 2017, 10:05:15 PM]

[October 16, 2017, 06:40:31 PM]

[October 16, 2017, 06:25:50 PM]

[October 16, 2017, 05:06:14 PM]

[October 16, 2017, 04:33:58 PM]

Support NCKA

Support the site by making a donation.

2017 AOTY/DOTY Entry

Topic: [How to] fix broken rod  (Read 262 times)

0 Members and 1 Guest are viewing this topic.

Chet

  • Salmon
  • ***
  • View Profile
  • Location: San Jose, California
  • Date Registered: Jun 2013
  • Posts: 892
Here is how I fixed it.


2016 Kayak_Crossing Catalina Island
http://www.norcalkayakanglers.com/index.php?topic=75214.0

2016 Dune Hobie AI
2011 Red Hobie AI
Trident 15
Tarpon 140


Spring45

  • Salmon
  • ***
  • View Profile
  • Location: Daly City
  • Date Registered: Feb 2017
  • Posts: 319
Thanks for sharing that!!


KPD

  • Salmon
  • ***
  • View Profile
  • Location: San Mateo
  • Date Registered: Jul 2014
  • Posts: 532
Nicely done, Chet.


Fisherman X

  • Sea Lion
  • ****
  • Going to the ocean is going home
  • View 's Album

  • View Profile
  • Location: Mendo Locos
  • Date Registered: Sep 2007
  • Posts: 3683
Nicely done, Chet.

Agreed. Keep us informed as to how it performs and holds up.
-Success is living the life you want-
Joel ><>


Scurvy

  • Salmon
  • ***
  • View Profile
  • Location: Alameda
  • Date Registered: Dec 2015
  • Posts: 355
I imagine the internal epoxy should be adequate since the splint transfers the loads across the joint and back into the rod tube.  If going without the external wrap, then it's probably better for the splint to fit somewhat loosely inside so that the epoxy is fully bonding it into place on all surfaces.

I hate to say it, but this is where buying the high-end rods pays off since most of the manufacturers/builders will provide replacement sections for these very problems.


Wildrooster

  • Salmon
  • ***
  • View Profile
  • Location: Valley springs
  • Date Registered: Oct 2015
  • Posts: 375
Good job
If you need to do it again try a Mylar wrap it will make it smoother except for the seam line we're the Mylar wrap started.
 you can easily sand down that edge which will be the thickness of the Mylar
the Mylar should extend well past the repair area and can be held in place with simple shipping tape
If you don't have Mylar you can use wax paper but depending on the quality you may want to use mold release to insure easy removal
When Mylar is use you don't need mold release it will naturally come off  as long as it's not held it place by excess fibers or resin
glade you made it
now let's get our fish on

Ascend FS128T
Hobie AI yellow


  • View 's Album

  • View Profile
  • Location: Placerville
  • Date Registered: Feb 2012
  • Posts: 2275
That's a really clean repair.  I'm not so meticulous with my fixes.

I use a BIC ball point pen.  Pull the inside out, leaving a clear plastic tube.  Cut to length, fill with epoxy and slide the two parts of the pole into the tube and let it set.  I keep a supply of individual use 2 part epoxy in my tackle and there's always a pen in the truck. 


 

anything